Date of Award
7-29-2026
Thesis Type
PhD
Document Type
Thesis
Degree Name
Doctor of Philosophy (PhD)
Divisions
Faculty of Dentistry
Department
Department of Restorative Dentistry
Institution
Universiti Malaya
Abstract
Advances in CAD/CAM restorative materials highlight the importance of selecting appropriate diamond rotary instruments to ensure efficient and conservative removal of high-strength ceramics during failure or retreatment procedures. This study evaluated the cutting efficiency, surface roughness, diameter changes and wear patterns of different high-speed diamond rotary instruments when used on contemporary CAD/CAM restorative materials. Six diamond rotary instrument types (NTI Kahla GmbH) were evaluated, including zirconia-specific Z-cut round-end cylinder instruments in medium (ZM) and fine (ZF) grits, as well as conventional round-end cylinder instruments in super coarse (SC), coarse (C), medium (M), and fine (F) grits were tested on monolithic zirconia+ (ZMONO), multi-transitional layered zirconia (ZMTL), advanced lithium disilicate (ALDS), and hybrid ceramic (HC) blocks. Each specimen was prepared at a standardised dimension of 14 x 12 x 2 mm. Cutting efficiency was determined by recording the time required for each instrument to transect the 2 mm thick specimens. Surface roughness (Ra, μm) was measured using a three-dimensional optical surface analyser, and instrument diameter was assessed with digital micrometer. Representative instruments from each group were examined for wear patterns before use and after the fifth cut using scanning electron microscopy. Statistical analysis was performed using two-way ANOVA with Tukey’s HSD post hoc test for multiple comparisons and one-way repeated measures ANOVA (p < 0.05). Instrument type and material significantly affected cutting time, surface roughness, and diameter with a significant interaction between factors (p < 0.05). Cutting efficiency declined from Cut-1 to Cut-5 for all instruments and materials. Cutting time increased as the materials became harder, following the order ZMONO > ZMTL > ALDS > HC. After cutting, ZMONO group showed lowest Ra of diamond rotary instruments, followed by ZMTL, ALDS, and HC. SEM analysis consistently showed least instrument wear when cutting HC, followed by ALDS < ZMTL < ZMONO groups. SC instruments showed highest cutting efficiency and Ra, with greater diameter change and wear. ZF instruments cut slowest with lowest Ra, minimal diameter changes and wear. Zirconia-specific diamond rotary instruments did not outperform conventional instruments. ZM instruments performed similarly to conventional F instruments. Conventional M instruments were statistically comparable with SC and C instruments in cutting efficiency and Ra, while exhibiting less diameter changes and instrument wear. Both instrument and material types exhibited variations in cutting efficiency, surface roughness, and diameter changes across all cutting intervals, with progressive reductions following repeated cuts and distinct wear patterns observed. Cutting efficiency decreased with increasing material strength, following the order ZMONO > ZMTL> ALDS > HC. At Cut-5, conventional SC, C, and M grit instruments showed significantly higher cutting efficiency and Ra than conventional F and zirconia-specific ZM instruments, whereas the zirconia-specific ZF instrument demonstrated the lowest performance. Diameter changes (deterioration) were greatest for SC, followed by ZM > F > C > M > ZF. Wear patterns differed between the two instrument types, with conventional diamond rotary instruments showing more attritious wear of diamond particles, whereas zirconia-specific diamond rotary instruments exhibited mainly particle pull-out and matrix abrasion.
Additional Information
Thesis (PhD) – Faculty of Dentistry, Universiti Malaya, 2026.
Recommended Citation
Yee Shien, Chung, "Evaluation of cutting efficiency, surface roughness and diameter of high-speed diamond rotary instruments in removal of CAD/CAM restorative materials" (2026). Student Works (2020-2029). 2037.
https://knova.um.edu.my/student_works_2020s/2037
Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-No Derivative Works 4.0 International License.
Included in
Dental Materials Commons, Equipment and Supplies Commons, Materials Science and Engineering Commons
Initial
khm