Date of Award

7-30-2026

Thesis Type

PhD

Document Type

Thesis

Degree Name

Doctor of Philosophy (Medical Science)

Divisions

Faculty of Dentistry

Department

Department of Restorative Dentistry

Institution

Universiti Malaya

Abstract

The clinical efficacy of surface treatment protocols for ceramic restorations and repairs is determined by the strength and durability of the lithium disilicate glass ceramic (LDGC) to resin bond. Although dental adhesives have undergone significant changes in their chemistry and compositions to create a durable bond, the research is still lacking on whether materials with greater technical simplicity or fewer operative phases exhibit superior performance. Aim: To investigate the shear bond strength (SBS) of IPS e. Max CAD and CEREC TesseraTM LDGC to conventional resin luting cement following various surface treatment protocols and to determine failure modes associated with these adhesive systems. Materials and Methods: 180 LDGC (90 IPS e. Max CAD and 90 CEREC TesseraTM ) specimens were prepared and randomly divided into 9 different surface treatment groups (n=10); Control [Hydrofluoric acid (HF) and Silane], Group 1 [HF and Glycerol-phosphate Di-methacrylate (GPDM) primer], Group 2 [HF and 10- methacryloyloxydecyldihydrogenphosphate (10-MDP) primer], Group 3 [HF +Silane+ resin-based adhesive], Group 4 [HF + GPDM adhesive], Group 5 [HF + 10-MDP adhesive], Group 6 [HF + Acid Resistant Silane (ARS)], Group 7 [HF + Silane + ARS], and Group 8 [HF +Silane + GPDM adhesive]. Resin luting cement was loaded onto the surface of LDGC using a predetermined dimension jig. All specimens were subjected to 5000 cycles of thermocycling at 5-55°C and SBS values were obtained via universal testing machine with a 500 N shear load and crosshead speed of 0.5 mm/min. For failure mode, all specimens were evaluated under a stereomicroscope and analysis was done using ImageJ software. Data for SBS were analysed using two-way ANOVA and post iv Hoc Tukey’s test. Failure modes were classified as adhesive, mixed and cohesive and were evaluated using the Pearson Chi-Square test. Results: For both IPS e. Max CAD and CEREC TesseraTM. LDGC, there was no statistical difference between the Control (silane), Group 1 (P-GPDM) and Group 2 (P-MDP) primers. However, Group 2 (P-MDP) demonstrated the highest mean shear bond strength for both LDGC, with values of 2.66 ± 0.81 MPa for IPS e. Max CAD and 3.42 ± 0.88 MPa for CEREC TesseraTM. Group 8 (SR-GPDM) demonstrated the highest SBS for both materials, with 5.88 ± 01.10 MPa for IPS e. Max CAD and 7.81 ± 2.16 MPa for CEREC TesseraTM. However, the difference between the two LDGC within this group was not statistically significant. Both Group 6 (ARS) and Group 7 (S-ARS) exhibited higher bond strength values than the Control (silane) for IPS e. Max CAD and CEREC TesseraTM, with Group 7 (S-ARS) showing the highest SBS value of 3.60 ± 0.30 MPa for IPS e. Max CAD and 3.67 ± 0.41 for CEREC TesseraTM. For IPS e. Max CAD specimens, adhesive failure was predominant across most groups, accounting for 96.7% of total failures. Group 5 exhibited the most diverse failure profile (80% adhesive, 10% mixed, 10% cohesive) and Group 8 presented 10% mixed failures. For CEREC TesseraTM, adhesive failure was predominant across most groups, with 87.8% of failures classified as adhesive. Notably, Group 5 demonstrated 30% adhesive, 50% mixed and 20% cohesive failures. Groups 6 and 8 also presented a small proportion of mixed failures (20%), whereas the remaining groups, including the control, exhibited exclusively adhesive failures. Conclusion: No significant difference was observed among 10-MDP, GPDM, and silane primers in enhancing SBS to traditional and advanced LDGC. HF etching combined with GPDM-based adhesive resin with or without silane pre-treatment is an effective approach to enhance bonding between both traditional and advanced LDGC and conventional resin luting cement. Adhesive resin containing acid-resistant silane may enhance surface treatment outcomes compared to conventional silane. Types of failures were associated with different surface treatments v of LDGC. Therefore, further research is warranted to conduct comparative analysis between GPDM-based adhesives and alternative adhesive systems, as well as to explore their bonding to both traditional and advanced LDGC.

Initial

khm

Additional Information

Thesis (PhD) – Faculty of Dentistry, Universiti Malaya, 2026.

Share

COinS